Ansys Workbench Verification Manual

Expand/Collapse all

VM-WB-MECH-001 - Statically Indeterminate Reaction Force Analysis
VM-WB-MECH-002 - Rectangular Plate with Circular Hole Subjected to Tensile Loading
VM-WB-MECH-003 - Modal Analysis of Annular Plate
VM-WB-MECH-004 - Viscoplastic Analysis of a Body (Shear Deformation)
VM-WB-MECH-005 - Heat Transfer in a Composite Wall
VM-WB-MECH-006 - Heater with Nonlinear Conductivity
VM-WB-MECH-007 - Thermal Stress in a Bar with Temperature Dependent Conductivity
VM-WB-MECH-008 - Heat Transfer from a Cooling Spine
VM-WB-MECH-009 - Stress Tool for Long Bar With Compressive Load
VM-WB-MECH-010 - Modal Analysis of a Rectangular Plate
VM-WB-MECH-011 - Large Deflection of a Circular Plate With Uniform Pressure
VM-WB-MECH-012 - Buckling of a Stepped Rod
VM-WB-MECH-013 - Buckling of a Circular Arch
VM-WB-MECH-014 - Harmonic Response of a Single Degree of Freedom System
VM-WB-MECH-015 - Harmonic Response of Two Storied Building Under Transverse Loading
VM-WB-MECH-016 - Fatigue Tool with Non-Proportional Loading for Normal Stress
VM-WB-MECH-017 - Thermal Stress Analysis with Remote Force and Thermal Loading
VM-WB-MECH-018 - A Bar Subjected to Tensile Load with Inertia Relief
VM-WB-MECH-019 - Mixed Model Subjected to Bending Loads with Solution Combination
VM-WB-MECH-020 - Modal Analysis for Beams
VM-WB-MECH-021 - Buckling Analysis of Beams
VM-WB-MECH-022 - Structural Analysis with Advanced Contact Options
VM-WB-MECH-023 - Curved Beam Assembly with Multiple Loads
VM-WB-MECH-024 - Harmonic Response of a Single Degree of Freedom System for Beams
VM-WB-MECH-025 - Stresses Due to Shrink Fit Between Two Cylinders
VM-WB-MECH-026 - Fatigue Analysis of a Rectangular Plate Subjected to Edge Moment
VM-WB-MECH-027 - Thermal Analysis for Shells with Heat Flow and Given Temperature
VM-WB-MECH-028 - Bolt Pretension Load Applied on a Semi-Cylindrical Face
VM-WB-MECH-029 - Elasto-Plastic Analysis of a Rectangular Beam
VM-WB-MECH-030 - Bending of Long Plate Subjected to Moment - Plane Strain Model
VM-WB-MECH-031 - Long Bar With Uniform Force and Stress Tool - Plane Stress Model
VM-WB-MECH-032 - Radial Flow due to Internal Heat Generation in a Copper Disk - Axisymmetric Model
VM-WB-MECH-033 - Spring Mass System Subjected to Enforced Motion with Displacement Base Excitations
VM-WB-MECH-034 - Rubber Cylinder Pressed Between Two Plates
VM-WB-MECH-035 - Thermal Stress in a Bar With Radiation
VM-WB-MECH-036 - Thermal Stress Analysis of a Rotating Bar Using Temperature-Dependant Density
VM-WB-MECH-037 - Cooling of a Spherical Body
VM-WB-MECH-038 - Crashing Blocks Simulation with Transient Structural Analysis
VM-WB-MECH-039 - Transient Response of a Spring-Mass System
VM-WB-MECH-040 - Deflection of Beam using Symmetry and Anti-Symmetry
VM-WB-MECH-041 - T-Stress Calculation for a Crack in a Plate Using Pre-Meshed Crack
VM-WB-MECH-042 - Hydrostatic Pressure Applied on a Square Bar Fully and Partially Submerged in a Fluid
VM-WB-MECH-043 - Fundamental Frequency of a Simply-Supported Beam
VM-WB-MECH-044 - Thermally Loaded Support Structure
VM-WB-MECH-045 - Laterally Loaded Tapered Support Structure
VM-WB-MECH-046 - Pinched Cylinder
VM-WB-MECH-047 - Plastic Compression of a Pipe Assembly
VM-WB-MECH-048 - Bending of a Tee-Shaped Beam
VM-WB-MECH-049 - Combined Bending and Torsion of Beam
VM-WB-MECH-050 - Cylindrical Shell Under Pressure
VM-WB-MECH-051 - Bending of a Circular Plate Using Axisymmetric Elements
VM-WB-MECH-052 - Velocity of Pistons for Trunnion Mechanism
VM-WB-MECH-053 - Simple Pendulum with Simple Harmonic Motion (SHM)
VM-WB-MECH-054 - Spinning Single Pendulum
VM-WB-MECH-055 - Projector Mechanism - Finding the Acceleration of a Point
VM-WB-MECH-056 - Coriolis Component of Acceleration (Rotary Engine Problem)
VM-WB-MECH-057 - Calculation of Velocity of Slider and Force by Collar
VM-WB-MECH-058 - Reverse Four Bar Linkage Mechanism
VM-WB-MECH-059 - Bending of a Solid Beam (Plane Elements)
VM-WB-MECH-060 - Crank Slot Joint Simulation with Flexible Dynamic Analysis
VM-WB-MECH-061 - Out-of-Plane Bending of a Curved Bar
VM-WB-MECH-062 - Stresses in a Long Cylinder
VM-WB-MECH-063 - Large Deflection of a Cantilever
VM-WB-MECH-064 - Small Deflection of a Belleville Spring
VM-WB-MECH-065 - Thermal Expansion to Close a Gap at a Rigid Surface
VM-WB-MECH-066 - Bending of a Tapered Plate
VM-WB-MECH-067 - Elongation of a Solid Tapered Bar
VM-WB-MECH-068 - Plastic Loading of a Thick Walled Cylinder
VM-WB-MECH-069 - Barrel Vault Roof Under Self Weight
VM-WB-MECH-070 - Hyperelastic Thick Cylinder Under Internal Pressure
VM-WB-MECH-071 - Centerline Temperature of a Heat Generating Wire
VM-WB-MECH-072 - Thermal Stresses in a Long Cylinder
VM-WB-MECH-073 - Modal Analysis of a Cyclic Symmetric Annular Plate
VM-WB-MECH-074 - Tension/Compression Only Springs
VM-WB-MECH-075 - Harmonic Response of Two-Story Building under Transverse Loading
VM-WB-MECH-076 - Elongation of a Tapered Shell With Variable Thickness
VM-WB-MECH-077 - Heat Transfer in a Bar with Variable Sheet Thickness
VM-WB-MECH-078 - Gasket Material Under Uniaxial Compression Loading-3-D Analysis
VM-WB-MECH-079 - Natural Frequency of a Motor-Generator
VM-WB-MECH-080 - Transient Response of a Spring-Mass System
VM-WB-MECH-081 - Statically Indeterminate Reaction Force Analysis
VM-WB-MECH-082 - Fracture Mechanics Stress for a Crack in a Plate
VM-WB-MECH-083 - Transient Response to a Step Excitation
VM-WB-MECH-084 - Mullins Effect on a Rubber Tube Model Subjected to Tension Loading
VM-WB-MECH-085 - Bending of a Composite Beam
VM-WB-MECH-086 - Stress Concentration at a Hole in a Plate
VM-WB-MECH-087 - Campbell Diagrams and Critical Speeds Using Symmetric Orthotropic Bearings
VM-WB-MECH-088 - Harmonic Response of a Guitar String
VM-WB-MECH-089 - Delamination Analysis of a Double Cantilever Beam Using Contact-Based Debonding
VM-WB-MECH-090 - Delamination Analysis of a Double Cantilever Beam Using Interface Delamination
VM-WB-MECH-091 - Unbalanced Harmonic Response of a Shaft Carrying Single Rotor with Damping
VM-WB-MECH-092 - Convection Treatment Problem for a Hollow Cylinder with Fluid Flow
VM-WB-MECH-093 - C*-Integral Calculation for a Single-Edge Cracked Plate Using Pre-Meshed Crack
VM-WB-MECH-094 - Residual Vector in Stand-Alone and Linked Mode-Superposition Harmonic Analysis
VM-WB-MECH-095 - 2-D Double Cantilever Beam Problem
VM-WB-MECH-096 - 2-D Fracture Problem Under Thermal Loading
VM-WB-MECH-097 - Inclined Crack in 2-D Plate Under Uniform Tension Loading
VM-WB-MECH-098 - 2-D End Notched Flexure Problem
VM-WB-MECH-099 - Mode I Crack Growth Analysis of DCB Using Interface Delamination
VM-WB-MECH-100 - 3-D Acoustic Modal Analysis with Temperature Change
VM-WB-MECH-101 - Natural Frequency of a Submerged Ring
VM-WB-MECH-102 - Topology Design of 2-D Beam with Clamped Ends
VM-WB-MECH-103 - Harmonic Response Analysis of a Piston-Fluid System
VM-WB-MECH-104 - Topology Optimization Benchmark Problem for Cantilever with End Load
VM-WB-MECH-105 - Motion of a Pendulum Under Gravity Load
VM-WB-MECH-106 - Motion of a Pendulum Under Gravity Load
VM-WB-MECH-107 - Cable/Pipe Supporting Hanging Loads
VM-WB-MECH-108 - Natural Frequency of a Piezoelectric Transducer
VM-WB-MECH-109 - Piezoelectric Rectangular Strip Under Pure Bending Load
VM-WB-MECH-110 - Centerline Temperature of an Electrical Wire
VM-WB-MECH-111 - Microstrip Transmission Line Capacitance
VM-WB-MECH-112 - Electrostatic Field Analysis of Quadpole Wires
VM-WB-MECH-113 - Electro-Thermal Microactuator Analysis

Additive Manufacturing Test Cases

VM-AM-MECH-001 - Additive Manufacture of Five-Post Beam Using Inconel 718
VM-AM-MECH-002 - Additive Manufacture of Thin-Walled Canonical Part Using Inconel 718
VM-AM-MECH-003 - Additive Manufacture of 3-Inch Double Cantilever with Supports Using Ti-6Al-4V
VM-AM-MECH-004 - Additive Manufacture of 4-Inch Double Cantilever with Supports Using Ti-6Al-4V
VM-AM-MECH-005 - Additive Manufacture of 5-Inch Double Cantilever with Supports Using Ti-6Al-4V
VM-AM-MECH-006 - Additive Manufacture of 70-mm Cantilever with Supports Using Inconel 625

Aqwa Test Cases

VM-AQWA-MECH-001 - Hydrostatic Evaluation of a Floating Inverted Pyramid
VM-AQWA-MECH-002 - RAOs for Hydrodynamic Diffraction System and Natural Modes for Hydrodynamic Response
VM-AQWA-MECH-003 - Motions of Adjacent Floating Structures in Oblique Waves
VM-AQWA-MECH-004 - Hydrodynamic Diffraction Analysis of a Barge with a Circular Moonpool

Design Exploration Test Cases

VM-DX-MECH-001 - Optimization of L-Shaped Cantilever Beam Under Axial Load
VM-DX-MECH-002 - Optimization of Bar with Temperature-Dependent Conductivity
VM-DX-MECH-003 - Optimization of Water Tank Column for Mass and Natural Frequency
VM-DX-MECH-004 - Optimization of Frequency for a Plate With Simple Support at all Vertices
VM-DX-MECH-005 - Optimization of Buckling Load Multiplier With CAD Parameters and Young's Modulus

Explicit Dynamics Test Cases

VM-EXD-MECH-001 - Flow of Gas Past an Infinite 2-D Wedge
VM-EXD-MECH-002 - 3-D Taylor Cylinder Impact
VM-EXD-MECH-003 - 2-D Taylor Cylinder Impact
VM-EXD-MECH-004 - 2-D Indirect Explosive Burn
VM-EXD-MECH-005 - 3-D Tension Failure Test (Cubes)
VM-EXD-MECH-006 - 3-D Shear Failure Test (Cubes)
VM-EXD-MECH-007 - Simple Pendulum with Simple Harmonic Motion (SHM)
VM-EXD-MECH-008 - Projector Mechanism -- Finding the Acceleration of a Point
VM-EXD-MECH-009 - Coriolis Component of Acceleration (Rotary Engine Problem)
VM-EXD-MECH-010 - Calculation of Velocity of Slider and Force by Collar
VM-EXD-MECH-011 - Reverse Four Bar Linkage Mechanism
VM-EXD-MECH-014 - Propagation of Shock and Rarefaction Waves in a Shock Tube
VM-EXD-MECH-015 - Regular and Mach Deflections Off of a 2-D Wedge
VM-EXD-MECH-016 - 3-D Burn on Time High Explosive Detonation

Material Designer Test Cases

VM-GEOM-SCMD-001 - Evaluation of Equivalent Orthotropic Material Properties for Multi-Layered Laminated Structures