Verification test cases for Mechanical include the following:
VM-WB-MECH-001
- Statically Indeterminate Reaction Force Analysis
VM-WB-MECH-002
- Rectangular Plate with Circular Hole Subjected to Tensile Loading
VM-WB-MECH-003
- Modal Analysis of Annular Plate
VM-WB-MECH-004
- Viscoplastic Analysis of a Body (Shear Deformation)
VM-WB-MECH-005
- Heat Transfer in a Composite Wall
VM-WB-MECH-006
- Heater with Nonlinear Conductivity
VM-WB-MECH-007
- Thermal Stress in a Bar with Temperature Dependent Conductivity
VM-WB-MECH-008
- Heat Transfer from a Cooling Spine
VM-WB-MECH-009
- Stress Tool for Long Bar With Compressive Load
VM-WB-MECH-010
- Modal Analysis of a Rectangular Plate
VM-WB-MECH-011
- Large Deflection of a Circular Plate With Uniform Pressure
VM-WB-MECH-012
- Buckling of a Stepped Rod
VM-WB-MECH-013
- Buckling of a Circular Arch
VM-WB-MECH-014
- Harmonic Response of a Single Degree of Freedom System
VM-WB-MECH-015
- Harmonic Response of Two Storied Building Under Transverse Loading
VM-WB-MECH-016
- Fatigue Tool with Non-Proportional Loading for Normal Stress
VM-WB-MECH-017
- Thermal Stress Analysis with Remote Force and Thermal Loading
VM-WB-MECH-018
- A Bar Subjected to Tensile Load with Inertia Relief
VM-WB-MECH-019
- Mixed Model Subjected to Bending Loads with Solution Combination
VM-WB-MECH-020
- Modal Analysis for Beams
VM-WB-MECH-021
- Buckling Analysis of Beams
VM-WB-MECH-022
- Structural Analysis with Advanced Contact Options
VM-WB-MECH-023
- Curved Beam Assembly with Multiple Loads
VM-WB-MECH-024
- Harmonic Response of a Single Degree of Freedom System for Beams
VM-WB-MECH-025
- Stresses Due to Shrink Fit Between Two Cylinders
VM-WB-MECH-026
- Fatigue Analysis of a Rectangular Plate Subjected to Edge Moment
VM-WB-MECH-027
- Thermal Analysis for Shells with Heat Flow and Given Temperature
VM-WB-MECH-028
- Bolt Pretension Load Applied on a Semi-Cylindrical Face
VM-WB-MECH-029
- Elasto-Plastic Analysis of a Rectangular Beam
VM-WB-MECH-030
- Bending of Long Plate Subjected to Moment - Plane Strain Model
VM-WB-MECH-031
- Long Bar With Uniform Force and Stress Tool - Plane Stress Model
VM-WB-MECH-032
- Radial Flow due to Internal Heat Generation in a Copper Disk - Axisymmetric Model
VM-WB-MECH-033
- Spring Mass System Subjected to Enforced Motion with Displacement Base Excitations
VM-WB-MECH-034
- Rubber Cylinder Pressed Between Two Plates
VM-WB-MECH-035
- Thermal Stress in a Bar With Radiation
VM-WB-MECH-036
- Thermal Stress Analysis of a Rotating Bar Using Temperature-Dependant Density
VM-WB-MECH-037
- Cooling of a Spherical Body
VM-WB-MECH-038
- Crashing Blocks Simulation with Transient Structural Analysis
VM-WB-MECH-039
- Transient Response of a Spring-Mass System
VM-WB-MECH-040
- Deflection of Beam using Symmetry and Anti-Symmetry
VM-WB-MECH-041
- T-Stress Calculation for a Crack in a Plate Using Pre-Meshed Crack
VM-WB-MECH-042
- Hydrostatic Pressure Applied on a Square Bar Fully and Partially Submerged in a Fluid
VM-WB-MECH-043
- Fundamental Frequency of a Simply-Supported Beam
VM-WB-MECH-044
- Thermally Loaded Support Structure
VM-WB-MECH-045
- Laterally Loaded Tapered Support Structure
VM-WB-MECH-046
- Pinched Cylinder
VM-WB-MECH-047
- Plastic Compression of a Pipe Assembly
VM-WB-MECH-048
- Bending of a Tee-Shaped Beam
VM-WB-MECH-049
- Combined Bending and Torsion of Beam
VM-WB-MECH-050
- Cylindrical Shell Under Pressure
VM-WB-MECH-051
- Bending of a Circular Plate Using Axisymmetric Elements
VM-WB-MECH-052
- Velocity of Pistons for Trunnion Mechanism
VM-WB-MECH-053
- Simple Pendulum with Simple Harmonic Motion (SHM)
VM-WB-MECH-054
- Spinning Single Pendulum
VM-WB-MECH-055
- Projector Mechanism - Finding the Acceleration of a Point
VM-WB-MECH-056
- Coriolis Component of Acceleration (Rotary Engine Problem)
VM-WB-MECH-057
- Calculation of Velocity of Slider and Force by Collar
VM-WB-MECH-058
- Reverse Four Bar Linkage Mechanism
VM-WB-MECH-059
- Bending of a Solid Beam (Plane Elements)
VM-WB-MECH-060
- Crank Slot Joint Simulation with Flexible Dynamic Analysis
VM-WB-MECH-061
- Out-of-Plane Bending of a Curved Bar
VM-WB-MECH-062
- Stresses in a Long Cylinder
VM-WB-MECH-063
- Large Deflection of a Cantilever
VM-WB-MECH-064
- Small Deflection of a Belleville Spring
VM-WB-MECH-065
- Thermal Expansion to Close a Gap at a Rigid Surface
VM-WB-MECH-066
- Bending of a Tapered Plate
VM-WB-MECH-067
- Elongation of a Solid Tapered Bar
VM-WB-MECH-068
- Plastic Loading of a Thick Walled Cylinder
VM-WB-MECH-069
- Barrel Vault Roof Under Self Weight
VM-WB-MECH-070
- Hyperelastic Thick Cylinder Under Internal Pressure
VM-WB-MECH-071
- Centerline Temperature of a Heat Generating Wire
VM-WB-MECH-072
- Thermal Stresses in a Long Cylinder
VM-WB-MECH-073
- Modal Analysis of a Cyclic Symmetric Annular Plate
VM-WB-MECH-074
- Tension/Compression Only Springs
VM-WB-MECH-075
- Harmonic Response of Two-Story Building under Transverse Loading
VM-WB-MECH-076
- Elongation of a Tapered Shell With Variable Thickness
VM-WB-MECH-077
- Heat Transfer in a Bar with Variable Sheet Thickness
VM-WB-MECH-078
- Gasket Material Under Uniaxial Compression Loading-3-D Analysis
VM-WB-MECH-079
- Natural Frequency of a Motor-Generator
VM-WB-MECH-080
- Transient Response of a Spring-Mass System
VM-WB-MECH-081
- Statically Indeterminate Reaction Force Analysis
VM-WB-MECH-082
- Fracture Mechanics Stress for a Crack in a Plate
VM-WB-MECH-083
- Transient Response to a Step Excitation
VM-WB-MECH-084
- Mullins Effect on a Rubber Tube Model Subjected to Tension Loading
VM-WB-MECH-085
- Bending of a Composite Beam
VM-WB-MECH-086
- Stress Concentration at a Hole in a Plate
VM-WB-MECH-087
- Campbell Diagrams and Critical Speeds Using Symmetric Orthotropic Bearings
VM-WB-MECH-088
- Harmonic Response of a Guitar String
VM-WB-MECH-089
- Delamination Analysis of a Double Cantilever Beam Using Contact-Based Debonding
VM-WB-MECH-090
- Delamination Analysis of a Double Cantilever Beam Using Interface Delamination
VM-WB-MECH-091
- Unbalanced Harmonic Response of a Shaft Carrying Single Rotor with Damping
VM-WB-MECH-092
- Convection Treatment Problem for a Hollow Cylinder with Fluid Flow
VM-WB-MECH-093
- C*-Integral Calculation for a Single-Edge Cracked Plate Using Pre-Meshed Crack
VM-WB-MECH-094
- Residual Vector in Stand-Alone and Linked Mode-Superposition Harmonic Analysis
VM-WB-MECH-095
- 2-D Double Cantilever Beam Problem
VM-WB-MECH-096
- 2-D Fracture Problem Under Thermal Loading
VM-WB-MECH-097
- Inclined Crack in 2-D Plate Under Uniform Tension Loading
VM-WB-MECH-098
- 2-D End Notched Flexure Problem
VM-WB-MECH-099
- Mode I Crack Growth Analysis of DCB Using Interface Delamination
VM-WB-MECH-100
- 3-D Acoustic Modal Analysis with Temperature Change
VM-WB-MECH-101
- Natural Frequency of a Submerged Ring
VM-WB-MECH-102
- Topology Design of 2-D Beam with Clamped Ends
VM-WB-MECH-103
- Harmonic Response Analysis of a Piston-Fluid System
VM-WB-MECH-104
- Topology Optimization Benchmark Problem for Cantilever with Central Load
VM-WB-MECH-105
- Motion of a Pendulum Under Gravity Load
VM-WB-MECH-106
- Motion of a Pendulum Under Gravity and Variable Load
VM-WB-MECH-107
- Cable/Pipe Supporting Hanging Loads
VM-WB-MECH-108
- Natural Frequency of a Piezoelectric Transducer
VM-WB-MECH-109
- Piezoelectric Rectangular Strip Under Pure Bending Load
VM-WB-MECH-110
- Centerline Temperature of an Electrical Wire
VM-WB-MECH-111
- Microstrip Transmission Line Capacitance
VM-WB-MECH-112
- Electrostatic Field Analysis of Quadpole Wires
VM-WB-MECH-113
- Electro-Thermal Microactuator Analysis