Once the battery model is enabled either in the graphical user interface or using the following text command:
define/models/battery-model
Enable battery model? [no] y
you can access the text user interface through the Console window by entering
define/models/battery-model/. A listing of the various text commands is
as follows:
-
define/models/battery-model/ Enters the battery model menu.
define/models/battery-model/battery-pack-builder/Enables the menu for the battery pack builder.
define/models/battery-model/battery-pack-builder/construct-battery-packConstructs the battery pack.
define/models/battery-model/battery-pack-builder/non-conformal-interface-matchingCreates non-conformal interfaces between the battery modules and the cold plate.
define/models/battery-model/battery-pack-builder/setup-pack-connectionSets battery connections.
define/models/battery-model/battery-rom-tool-kit/Enters the menu for the battery ROM took kit. See Using the Battery ROM Tool Kit in the Fluent User's Guide for details about the below text commands.
define/models/battery-model/battery-rom-tool-kit/add-item-to-face-heat-listAllows you to specify heat fluxes through the selected faces.
define/models/battery-model/battery-rom-tool-kit/add-item-to-face-temperature-listAllows you to specify temperature at the selected faces.
define/models/battery-model/battery-rom-tool-kit/add-item-to-lti-output-cell-listAdds the selected cell zones to the list of the LTI output parameters. This text command is available only for the LTI-ROM.
define/models/battery-model/battery-rom-tool-kit/add-item-to-lti-output-face-listAdds the selected face zones to the list of the LTI output parameters. This text command is available only for the LTI-ROM.
define/models/battery-model/battery-rom-tool-kit/add-item-to-lti-output-point-listAdds the selected user-created points to the list of the LTI output parameters. This text command is available only for the LTI-ROM.
define/models/battery-model/battery-rom-tool-kit/add-item-to-lti-output-report-definition-listAdds the selected report definitions that you previously created to the list of the LTI output parameters. This text command is available only for the LTI-ROM.
define/models/battery-model/battery-rom-tool-kit/add-item-to-lti-output-surface-listAdds the selected surfaces that you previously created to the list of the LTI output parameters. This text command is available only for the LTI-ROM.
define/models/battery-model/battery-rom-tool-kit/add-item-to-svd-zone-listAdds the selected cell zones for which you want to export temperature information to the list of the SVD output parameters. This text command is available only for the SVD-ROM.
define/models/battery-model/battery-rom-tool-kit/add-item-to-volume-heat-listAllows you to specify heat sources in the selected volumes.
define/models/battery-model/battery-rom-tool-kit/delete-item-from-listDeletes the specified ROM parameter. The name of the parameter must be entered in double quotes.
define/models/battery-model/battery-rom-tool-kit/file-saving-frequencyAllows you to specify the frequency with which the solution files should be saved.
define/models/battery-model/battery-rom-tool-kit/list-rom-related-listsPrints information on all ROM-related lists in the Fluent console.
define/models/battery-model/battery-rom-tool-kit/lti-rom-generationSets up the LTI-ROM generation tool.
define/models/battery-model/battery-rom-tool-kit/rom-data-creatorSelects the ROM type (LTI or SVD).
define/models/battery-model/battery-rom-tool-kit/transient-setupAllows you to set up the transient solver.
define/models/battery-model/cht-coupling-parametersAllows you to define the total heat source for each battery active zone for the CHT coupling solution method.
-
define/models/battery-model/ecm-parameters Sets ECM model-specific parameters (see Inputs for the Equivalent Circuit Model for definitions of the ECM model parameters).
-
define/models/battery-model/electric-field-model/ Enters the electric field setup menu.
-
define/models/battery-model/electric-field-model/conductive-regions Specifies active conductive regions.
-
define/models/battery-model/electric-field-model/contact-resistance-regions Specifies contact resistance regions.
-
define/models/battery-model/electric-field-model/current-tap Sets cathode tap.
-
define/models/battery-model/electric-field-model/voltage-tap Sets anode tap.
-
-
define/models/battery-model/enable-battery-model? Enables/disables battery model.
define/models/battery-model/fmu-coupling-parametersAllows you to hook up FMU output parameters to the Ansys Fluent parameters for the FMU-CHT coupling solution method.
define/models/battery-model/include-entropic-heat?Includes entropic heat in the heat source calculation and sets the entropic heat definition method. See Including the Entropic Heat Effects in the Fluent User's Guide for details.
-
define/models/battery-model/model-parameters Sets battery model options (see Specifying Battery Model Options for definitions of the model general parameters).
-
define/models/battery-model/newman-parameters Sets Newman model-specific parameters (see Inputs for the Newman’s P2D Model for definitions of the Newman model parameters).
-
define/models/battery-model/ntgk-parameters Sets NTGK model-specific parameters (see Inputs for the NTGK/DCIR Model for definitions of the NTGK model parameters).
-
define/models/battery-model/parameter-estimation-tool Computes the model parameters from battery's testing data. You can use the estimation tool to compute model parameters for the NTGK or ECM model, or for the One-Equation thermal abuse model. You must provide battery's testing data as a text file in a specific format for each model. When you enable this tool and select the model option, Fluent will show the required format for the input file in the console. For more details, see Using Parameter Estimation Tools. You can contact Ansys Technical Support for clarifications on how to use this tool.
define/models/battery-model/run-echem-model-standaloneAllows you to run the electro-chemistry models and the physics-based battery life model in the standalone mode. For more information, see Running the Standalone Echem Model and Simulating the Aging Process of a Battery (Standalone Mode) in the Fluent User's Guide.
define/models/battery-model/solution-methodSets solution method options (see Specifying Battery Model Options in the Fluent User's Guide for details).
define/models/battery-model/swelling-model-parametersSets parameters for the swelling model (see Inputs for the Newman’s P2D Model and Using the Empirical-Based Battery Swelling Model in the Fluent User's Guide for details).
define/models/battery-model/thermal-abuse-modelAllows you to choose a thermal abuse model and specify its parameters (see Specifying Advanced Options in the Fluent User's Guide for more details).
-
define/models/battery-model/use-orthotropic-material? Defines orthotropic thermal conductivity for the battery material (see Defining Orthotropic Thermal Conductivity in the Fluent User's Guide for details).
-
define/models/battery-model/venting-model Allows you to enable the venting model and specify its parameters (see Battery Venting Model in the Fluent Theory Guide for details).
-
define/models/battery-model/user-defined-emodel-parameters Sets specific parameters for the user-defined model (see Input for the User-Defined E-Model for definitions of the model parameters).