• 1. Introduction to Ansys 3D Design Test Cases
  • 1.1. Project and Input Files
  • 1.2. How to Download and Run the 3D Design Project Files
• 2. Discovery Application Test Cases
  • 2.1. Discovery Structural Test Cases
    • 2.1.1. STRUCT-001 Rectangular Plate with Circular Hole Subjected to Tensile Loading
    • 2.1.2. STRUCT-002 Elongation of a Solid Bar
    • 2.1.3. STRUCT-003 Laterally Loaded Tapered Beam
    • 2.1.4. STRUCT-004 Circular Plate Under Uniform Pressure
    • 2.1.5. STRUCT-005 Two Bar Assembly with Frictionless Contact
    • 2.1.6. STRUCT-006 Stress Concentration in a Shaft with a Shoulder Fillet
    • 2.1.7. STRUCT-007 Sphere under Internal Pressure
    • 2.1.8. STRUCT-008 Shaft under Torque Load
  • 2.2. Discovery Modal Test Cases
    • 2.2.1. MODAL-001 Cantilever Beam Modal Analysis
    • 2.2.2. MODAL-002 Simply Supported Beam Modal Analysis
    • 2.2.3. MODAL-003 Modal Analysis of an Annular Plate
    • 2.2.4. MODAL-004 Modal Analysis of a Rectangular Plate
    • 2.2.5. MODAL-005 Vibration of a Rotating Cantilever Blade
  • 2.3. Discovery Thermal Test Cases
    • 2.3.1. THERM-001 Heat Transfer in a Composite Wall
    • 2.3.2. THERM-002 Conduction in a Composite Solid Block
    • 2.3.3. THERM-003 Heat Transfer from a Cooling Spine
    • 2.3.4. THERM-004 Thermal Stress in a Bar with Temperature Dependent Thermal Conductivity
    • 2.3.5. THERM-005 Deflection of Bimetallic Cantilever under Thermal Load
    • 2.3.6. THERM-006 Centerline Temperature of an Electrical Wire
  • 2.4. Discovery Fluid Test Cases
    • 2.4.1. FLUID-001 Laminar Flow Through a Pipe
    • 2.4.2. FLUID-002 Laminar Flow Through a Pipe with Uniform Heat Flux
    • 2.4.3. FLUID-003 Pressure Drop in Turbulent Flow Through a Pipe
    • 2.4.4. FLUID-004 Natural Convection in a Concentric Annulus
    • 2.4.5. FLUID-005 Radiation Heat Transfer in an Enclosure
    • 2.4.6. FLUID-006 Laminar Flow Over a Sphere
    • 2.4.7. FLUID-007 Laminar Flow Between Rotating and Stationary Cylinders
    • 2.4.8. FLUID-008 Laminar Flow in a 90° T-Junction
  • 2.5. Discovery Solutions of NAFEMS Benchmarks
    • 2.5.1. BMTTA, No. 9(i)
    • 2.5.2. BMTTA, No. 15(i)
    • 2.5.3. BMTTA, No. 15(iii)
    • 2.5.4. LSB1, No. IC 19
    • 2.5.5. LSB1, No. IC 29
    • 2.5.6. LSB1, No. IC 39
    • 2.5.7. P09-T4
    • 2.5.8. P09-T6
    • 2.5.9. P09-T15
    • 2.5.10. P09-T33
  • 2.6. Discovery Modeling Test Cases
    • 2.6.1. MODELING-001 Alter Model Using Sketch, Pull, and Fill
    • 2.6.2. MODELING-002 Alter Model Using Split Face, Split Body, and Mirror
    • 2.6.3. MODELING-003 Alter Model using Linear, Circular, and Two-Dimensional Patterns
    • 2.6.4. MODELING-004 Alter Model Using Revolve, Chamfer, and Offset Faces
    • 2.6.5. MODELING-005 Alter Model Using Blend and Project
  • 2.7. Discovery Preparing Test Cases
    • 2.7.1. PREPARING-001 Volume Extract and Enclosure
    • 2.7.2. PREPARING-002 Beam Create, Extract, and Orient
    • 2.7.3. PREPARING-003 Remove Rounds, Interference, Faces, and Short Edges
    • 2.7.4. PREPARING-004 Midsurface, Extend, Imprint, and Weld
  • 2.8. Discovery Repairing Test Cases
    • 2.8.1. REPAIRING-001 Stitch, Gap, and Missing Faces
    • 2.8.2. REPAIRING-002 Simplify, Small Faces, Merge Faces
    • 2.8.3. REPAIRING-003 Split Edges, Extra Edges, and Duplicates
• 3. SpaceClaim Application Test Cases
  • 3.1. SpaceClaim Geometry Test Cases
    • 3.1.1. GEOM-001 Alter Model Using Sketch, Pull, and Fill
    • 3.1.2. GEOM-002 Alter Model Using Split Face, Split Body, and Mirror
    • 3.1.3. GEOM-003 Alter Model using Linear, Circular, and Two-Dimensional Patterns
    • 3.1.4. GEOM-004 Alter Model Using Revolve, Chamfer, and Offset Faces
    • 3.1.5. GEOM-005 Alter Model Using Blend and Project
    • 3.1.6. GEOM-006 Alter Model Using Sheet Metal Tools and Operations
  • 3.2. SpaceClaim Preparing Test Cases
    • 3.2.1. PREPARING-001 Midsurface, Extend, Imprint, and Spot Weld
    • 3.2.2. PREPARING-002 Volume Extract and Enclosure
    • 3.2.3. PREPARING-003 Beam Create, Extract, and Orient
    • 3.2.4. PREPARING-004 Remove Rounds, Interference, Faces, and Short Edges
  • 3.3. SpaceClaim Repairing Test Cases
    • 3.3.1. REPAIRING-001 Stitch, Gap, and Missing Faces
    • 3.3.2. REPAIRING-002 Straighten, Simplify, Small Faces, Merge Faces
    • 3.3.3. REPAIRING-003 Split Edges, Extra Edges, and Duplicates
• 4. DesignModeler Application Test Cases
  • 4.1. DesignModeler Geometry Test Cases
    • 4.1.1. GEOM-001 Extrude, Chamfer, and Blend
    • 4.1.2. GEOM-002 Revolve, Sweep, Extrude, and Skin-Loft
    • 4.1.3. GEOM-003 Extrude, Revolve, Skin-Loft, and Sweep
    • 4.1.4. GEOM-004 Extrude, Revolve, Skin-Loft, and Sweep
• i. Copyright and Trademark Information